Repository navigation
missing frames #1954
Description
Did you read the guide?
Yes
What is the base version number of Motion being used?
5.2.x
What was the install method?
Built from source code
What is base architecture?
x86/x64
What is the distro being used?
Debian
Disto version number
13.4
Camera/Sound type(s) being used?
Network camera with RTSP
Describe the issue/problem and steps to reproduce
motion build from current master.
In every recorded video a lot of frames are missing.
Here a example picture_output:
And here the recorded Video:
https://github.com/user-attachments/assets/765d531f-d75a-4660-adf8-aa2ba924b468
The guy from the picture is not in the video.
And this way all my recordings are :-(
Relevant Motion log output (at log_level 8)
picture_filename %CTerrasse
movie_filename %CTerrasse
width 640
height 480
framerate 31
movie_passthrough on
movie_all_frames off
minimum_motion_frames 28
event_gap 33
pre_capture 2
post_capture 4
picture_output best
threshold 2000
netcam_high_params allowed_media_types=video
netcam_url rtsp://xxx/Preview_01_sub
netcam_high_url rtsp://xxx/Preview_01_main
Activity
tosiara commentedon Apr 20, 2026
what is the timestamp on the photo?
dia-de-muertos commentedon Apr 20, 2026
hm, don't realy know
filename is 11.04.41Terrasse.jpg
so possibly 11:04:41, which is after the recording stopped
dia-de-muertos commentedon Apr 21, 2026
hm, timesamp of imgae is 09:13:53
here the recorded video:
https://github.com/user-attachments/assets/94d6bc75-fd08-4046-accb-cc6871b2836e
is in the middle but the bird is not visible
tosiara commentedon Apr 21, 2026
I cannot see 09:13:53 on the picture, while video contains that timestamp and not the bird. Are you sure about the picture and the timestamp? Sometimes stream and substream may be not in sync, so you may see such weird recordings. Increasing pre- and post-capture may help, as well as adjusting camera's encoding to have all key frames or set it to CBR.
Also you can try to enable
movie_output_motionwhich will record changed pixels only so you can try to debug (https://motion-project.github.io/motion_config.html#movie_output_motion)tosiara commentedon Apr 21, 2026
And I mean the timestamp that camera prints on the image, not motion's timestamp
dia-de-muertos commentedon Apr 21, 2026
That's my problem, the timestamp is not readable.
I will try to save larger/less compressed images and
also increase pre-/post-capture and enable movie_output_motion
Mr-Dave commentedon Apr 21, 2026
Have you looked to see if there were multiple movies created during the event? Either in the log or in the directory. Or that the movie names are not overlapping and over writing each other? i.e. A second movie during the last part of the event is not overwriting a movie created during the first part of the event.
Based upon the camera timestamps and playback duration, it looks like all the frames were recorded so just not sure if the bird was there during a time before or after this movie. (Recall that the "best" picture per event and there can be multiple movies per event. So the "best" image is not going to be in every movie created.)
dia-de-muertos commentedon Apr 21, 2026
No, there's only one movie, also only one recording in the logfile.
Now I've set precapture to 4 and postcapture to 8.
First tests are good. I little bit to much frames after the event (about 8-9 seconds),
but better then before, where the event was not visible.
Will wait a couple of days to see if it stays ok.