Replies: 7 comments 21 replies
-
|
Sensor not compatible or not programt. Possible you have to clone the old sensors |
Beta Was this translation helpful? Give feedback.
-
|
If so, how was everything ok for 1 day after I manually wrote sensor IDs? How to clone them? |
Beta Was this translation helpful? Give feedback.
-
|
You either need original sensors that are already described or are looking for how you can clone from the original sensors. NOT from Chinese store !!!!!! |
Beta Was this translation helpful? Give feedback.
-
|
This is not an answer... But I have currently got the same problem, which is why I've just got DDT4ALL set up to investigate. I used 4 new sensors from AliExpress, and programmed the codes in the 2015 Megane 3 CC GT-Line using a Foxwell 680 Pro. |
Beta Was this translation helpful? Give feedback.
-
|
in DDT4ALL if your cars ECU's have settings for 'Direct TPMS' and 'Indirect TPMS' try both - (but I think it should be indirect TPMS myself) one uses sensors in the valves the other uses sensors by ABS I think. |
Beta Was this translation helpful? Give feedback.
-
|
I'm waiting on a new Battery for the car before I scan it to see what's going on, but mine is a late model Megane Mk3 . It looks like there are 6 or more console options for the ECU, so I'm hoping DDT4ALL will correctly identify mine or I'll be writing data in the wrong space. |
Beta Was this translation helpful? Give feedback.
-
|
I got my new battery...old one tested at 66%... Put it in the car and started it...no warning lights, car started almost instantly... Left the car unused for a fortnight for various reasons and put the charger on for a day before taking out for the first time with the new battery... I was expecting it to run for 10-15: minutes and then realise it could not read TPMS sensors, so I hadn't even scrolled through to see if readings were there. |
Beta Was this translation helpful? Give feedback.
-
|
Hello! I have exactly the same problem. An error message appears: “Check the tire pressure sensor.” The pressure is normal (2.2-2.3bar). The wiper switch button does not reset this error. You have to remove the battery terminal to clear this error. There is no error for several days and I can drive 100-200 km without an error. Then the error pops up again. And again you have to remove the battery terminal. |
Beta Was this translation helpful? Give feedback.
-
|
I'm still working on a permanent solution... my temporary one was to install a remote battery isolator which was £20 on AliExpress or £25 on eBay... If I disconnect for 25 minutes (disconnect after locking but before alarm arms) then I get 12 restarts of the engine...after the last start you get about a kilometre and although all 4 tyre pressures show OK, they all then disappear... NOT a function of Distance, purely the number of starts. |
Beta Was this translation helpful? Give feedback.
-
|
Hello; Years have passed but I wanted to write about the problem I experienced. I wanted to add this feature that was not originally in my vehicle but had an infrastructure. 3 of the sensors I received from my part are different brands, 1 is original VDO. Since the part is familiar, I bought it on the condition of returning it. I introduced it with dtt4all without installing it on the tires, but since it was not installed, after a while I received a flat tire warning and after a while I received a warning that the tire sensor could not be detected and the tire symbols on the dial disappeared. We thought this was normal and installed the sensor during the winter tire change yesterday. However, when I wanted to introduce it again in the evening, I could only introduce the VDO one. When I find the opportunity, I will repeat the processes I did from the beginning and give information here. The introduction process was completed after a long effort. In fact, a nail got into one tire and I understood it thanks to the sensor. The tire repaired it but I think he pressed 40 psi after the repair and 3 sensors except VDO could not be detected. When I connected with PyREN, I saw that VDO was "status 1" and the others were "status 2". The pressure was showing as 3.5 bar. I lowered the pressure and when I increased it to about 20 psi, it suddenly detected the sensor and gave a flat tire warning. However, when I pressurized it to 30 psi, it still could not detect the sensors. I could not understand what to do. |
Beta Was this translation helpful? Give feedback.
-
|
For those who have problem with disappearing TPMS sensor reading after few days I have recommendation to change PARA_LOC_LEARNING_DEFAULT from 10 to 255. This will extend time left to next battery disconnection to around 5 months. |
Beta Was this translation helpful? Give feedback.
-
|
At the risk of appearing rude...no I'm not doing anything wrong.. disabling the TPMS on this car requires more than one action...if you can't provide useful information, then please do not comment, but if you know exactly what to do then feel free to leave appropriate information...thanks.. |
Beta Was this translation helpful? Give feedback.
-
|
Hmmm oke her 18y specialist.
|
Beta Was this translation helpful? Give feedback.
-
|
To Renotech1... |
Beta Was this translation helpful? Give feedback.
-
|
I just trying to help bro.. I just say what you try to do .. in tdb to disable... i even send you screenshot..
|
Beta Was this translation helpful? Give feedback.
-
|
I don't remember correctly but if it can help you... |
Beta Was this translation helpful? Give feedback.
-
|
I had disconnected the battery cable yesterday. When I connected it today, the left front sensor code that I had entered incorrectly before appeared. When I corrected the left front sensor code, all sensors worked without any problems. If the same thing happens again, I will enter all sensor codes as "000000", disconnect the battery cable and then enter them correctly. I also increased the PARA_LOC_LEARNING_DEFAULT value from 10 to 255. |
Beta Was this translation helpful? Give feedback.
-
|
Hello all! So, every year it's the same. Thank you! 🙂 |
Beta Was this translation helpful? Give feedback.
-
|
when I had my Clio4 I had to change the presence spp to 0 in the BCM/uch ECU as well as turn it off on the dash 
Dont forget when you change the setting in your cluster you have to also press on prise en complet button afterwards. 
Good luck |
Beta Was this translation helpful? Give feedback.
-
|
That highlights my problem with turning it off...I can't identify which dash I should select. |
Beta Was this translation helpful? Give feedback.
-
|
are you searching for the dash/cluster with the magnifying glass |
Beta Was this translation helpful? Give feedback.
Uh oh!
There was an error while loading. Please reload this page.
Uh oh!
There was an error while loading. Please reload this page.
-
Hi all!
Recently I bought 4 new sensors from aliexpress and had them installed.
After a few miles they were not recognized and I got a red warning to check my sensors.
First, in dashboard I got to tpms menu, held a button for 5sec and got message that pressure ref is active or something like that but the error didn't dissapear after that.
Then, in DDT4ALL I went to BCM, TPMS extra screen and wrote IDs from those new sensoes. Then drove a couple of hundred meters and they were all read and pressure was shown on dashboard. Excellent, I thought.
The next day, I went home from work and the red message appeared again. No pressures showing, I hold the button for 5sec again and no results. In DDT the IDs I wrote are still there.
Anyone knows whats happening?
Are batteries in sensors dead?
Thanks!
EDIT: Also, in DDT4ALL I see there are two labels (jeu ete and jeu hiver) for summer and winter wheel set but I can only write sensor IDs in one label (see pic). Why is that?
Beta Was this translation helpful? Give feedback.
All reactions